Napco Security Technologies GEM-K2AS Manual de usuario Pagina 33
- Pagina / 36
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
33
GLOSSARY
Instant Protection
- Arming without
entry delay by pressing and holding
the
P button while remaining on
the premises.
Keypad
- Puts control-panel
functions at your fingertips. It can be
mounted anywhere in your premises.
Manager's Mode - In a partitioned
system, a low-security operating
mode that allows arming by area.
Opening Window - (Optional). A
time interval within which opening
(disarming) is permitted without re-
porting to the central station.
Overview Mode - In a partitioned
system, a high-security mode of op-
eration allowing area arming wherein
the status of Areas 1 and 2 is simul-
taneously displayed at the keypad.
Panic Buttons
- Blue buttons on
the keypad (
G and 7,
8 or 9). If enabled,
pressing
G
together with
7
,
8
or
9
will alert the central
station of a fire, auxiliary, or police
emergency.
Partitioned System - A system that
has been subdivided into two or more
(up to eight) independent subsystems
(areas).
Pre-Alarm Warning. - A keypad
sounder alert of an impending alarm.
This option is programmable by zone
for the same duration as that
programmed for Abort Delay (see
Abort Delay).
Report - A transmission to a central
station notifying of a change in the
status of the system (alarm, trouble,
low battery, etc.).
Ringback - A beep after arming
verifying the central-station's receipt
of a closing report.
Service Code - A code intended for
temporary use.
Sounder - A local warning device
at each keypad to alert that (a) entry
delay has started; (b) an attempt was
made to arm with a zone in trouble;
(c) a Day-Zone condition exists (see
Zones: Day Zone); (d) 10 seconds
exit time remaining; (e) invalid code
entered; or (f) central station
acknowledged arming (see
Ringback).
System Trouble
- A problem (low
battery, power failure, etc.) detected
in the system.
Trouble
- A zone fault; an open
door, window, or other problem that
may prevent arming.
User Code - Your personalized
code for arming and disarming the
system. It may contain up to six
digits.
- OPERATING GUIDE for your 1
- INTRODUCTION 2
- TABLE OF CONTENTS 3
- PRIOR / NO 4
- NEXT / YES 4
- P when the 5
- BYPASSED 6
- Area Arming (Optional) 8
- Manager's Mode 8
- Global Arming 8
- Easy Exit 9
- Instant Protection 10
- Emergency Buttons 10
- FIRE PROTECTION 13
- FUNCTION MENU 17
- CENTRAL STATION MONITORING 22
- ADVANCED FEATURES 23
- G button 25
- G 0, then 26
- G, 0 to clear 26
- PROGRAMMING (OPTIONAL) 27
- KEYPAD MESSAGES 28
- GLOSSARY 32
- SYSTEM TROUBLE ERROR CODES 35
- NAPCO LIMITED WARRANTY 36
Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad Napco Security Technologies GEM-K2AS
Los Sistemas De Control De Acceso De Seguridad Napco Security Technologies GEMINI GEM-P400 Manual de usuario
(16 paginas)
(16 paginas)
Los Sistemas De Control De Acceso De Seguridad Napco Security Technologies GEM-P1632 Manual de usuario
(16 paginas)
(16 paginas)
Los Sistemas De Control De Acceso De Seguridad Napco Security Technologies GEM-DXRP2 Manual de usuario
(36 paginas)
(36 paginas)
Los Sistemas De Control De Acceso De Seguridad Napco Security Technologies XP-400 Manual de usuario
(28 paginas)
(28 paginas)
Los Sistemas De Control De Acceso De Seguridad Napco Security Technologies GEM-DXK3 Manual de usuario
(32 paginas)
(32 paginas)
Los Sistemas De Control De Acceso De Seguridad Napco Security Technologies GEM-K1CA Manual de usuario
(40 paginas)
(40 paginas)
APC 2000VA manuales
Manuales del propietario y guías del usuario para Sistemas De Alimentación Ininterrumpida (Sai) APC 2000VA.
Ofrecemos 1 manuales en pdf APC 2000VA para descargar gratis por tipos de documentos: Manual de usuario
Comentarios a estos manuales