Napco Security Technologies XP-400 Manual de usuario

XP-400 & RPXP4GT keypad Control Panel/Communicator Installation Instructions WI1370 1/05 © NAPCO 2005 ®

10WI1370 XP-400 Installation Instructions While in User Program Mode the W Armed, X READY and HSystem Trouble LEDs will continue to flash,

11Dealer Commands A6 Download (Programming Required) Establish a connection between the PCD phone line and the Control Panel phone line. When ready,

12WI1370 XP-400 Installation Instructions To eliminate this fixed 20-second entry delay, also program zones as Exit/Entry Follower Zones [02]. To r

13[08]PGM Output Enables the PGM Output on a zone trip for each zone selected. The PGM Output will remain ON until reset. System Times [10]Exit De

14WI1370 XP-400 Installation Instructions [21]Keypad Features 2 (1) Audible Panic - Keypad Panic will not turn the Bell on unless this option is prog

15(3) Panic - Program to activate the PGM on a Panic alarm. (4) Test Timer - Program to activate the PGM during a Test Timer report. [25]Programmable

16WI1370 XP-400 Installation Instructions Pager Alarm data is the same as 4/2 format with the exception that the 2 digit Report Code is trans

17[37]System Reporting, Telco 1 (1) Y AC Fail Report - Program to activate an AC Fail report (15 minute fixed report delay). (2) Low Battery Report -

18WI1370 XP-400 Installation Instructions Telephone Number 3 Programming [50] - [59] Programming is the same as for Telco 1. Program to split/dou

19[66]Ambush Report Code Program a 2-digit report code for Ambush. To send an ambush report, program a User Code for User 4, Program report User 4 as

2WI1370 XP-400 Installation Instructions General Information The NAPCO EXPRESS XP-400 control panel provides up to 4 hardwired/wireless zones. Up t

20WI1370 XP-400 Installation Instructions [71-74] Wireless Transmitters Enter the RF ID# and the point number that is to be mapped to the zone. Prog

217 Full Set System Program a 7 in the AUX 1 and/or AUX 2 option to Fully Set the System when the K and the M or N buttons on the Keyfob are pressed,

22WI1370 XP-400 Installation Instructions Site At the site perform the following three steps: 1. Arm the panel. 2. Disarm the panel. 3. Enter A6. Th

23System Troubles Use the System Trouble chart on the following page to determine the specific System Trouble(s). During normal panel operation the

24WI1370 XP-400 Installation Instructions Keypad Beeps or H SYSTEM Flashes Zone LED ON System Trouble Condition Cause/Action 1 Beep Y LED 1 Y AC Po

25Troubleshooting 1. The bell output drops to about 3 volts in alarm. The battery/bell circuit is protected by a PC board trace which may have burned

26WI1370 XP-400 Installation Instructions 8. How do I remove Keypad Sounder on Alarm? The keypad sounder follows the Burg Output. If you need to remo

2716 VAC 20 VA TRANSFORMER NAPCO TRF12 (OR EQUIVALENT SEE WI1370). Class 2 Transformer. (3) -4 +5 +6 1 2 +3 GEM-RECV

NAPCO LIMITED WARRANTY NAPCO SECURITY SYSTEMS, INC. (NAPCO) warrants its products to be free from manufacturing defects in materials and workmanship f

3Specifications Current & Voltage Ratings Alarm Output -------------------------- Burg: 12 VDC, 2A (max.) Output Current Limit

4WI1370 XP-400 Installation Instructions 4 zone Control Panel Keypad Zone Doubling Resistors (2.2K & 3.9K) Operating Instructions XP-400 Programm

5 Programming the Panel Refer to XP-400 Programming Instructions (WI1371) Defaulting the Panel 1. Remove power from the panel. 2. Remove all wiring

6WI1370 XP-400 Installation Instructions Installation Mounting the Panel Mount the Panel close to an unswitched AC source, a cold-water pipe ground,

7PGM Wiring The PGM is a switched negative output that is activated depending on the programming option(s) that have been selected [08], [23] - [25].

8WI1370 XP-400 Installation Instructions Arming/Disarming with a Keyfob The system can be armed by pressing the K key, and disarmed by pressing the

9Full Setting the System with Automatic Bypassing - Home/Away with Delay Zones From the Keypad Press C B to return protection to Home/Away with Del