1OPERATING GUIDE for yourGEM-RP3DGTL KEYPAD© NAPCO 1999 DESIGN PATS. PENDINGRCOMPUTERIZED SECURITY SYSTEMARMEDSTATUSSYSTEM ARMEDSYSTEM ARMED01/01/97

10TURNING OFF THE ALARM (DISARMING) WHEN RETURNING1. Upon entry, the red ARMED light will be on and the keypad sounder will come on as a reminder to d

11TURNING OFF THE ALARM (DISARMING) WHEN RETURNINGAmbush (Ambush programmed? YES NO.)The Ambush Code (optional) is a 2-digit code that is ente

12FIRE PROTECTION(Applicable only where local ordinance permits use of this alarm control panel for fire protection.)Fire-Zone AlarmIf a fire is detec

13FIRE PROTECTIONPreparing a Fire Escape PlanEven with the most advanced firealarm system, adequate protection re-quires an escape plan.To prepare you

14FIRE PROTECTIONFloorplanDraw a plan of your premises in the space provided below.FloorplanGEM-RP3DGTL.pub page 14Wednesday, August 18, 1999 14:03

15FIRE PROTECTIONAlthough a fire alarm system may be of a reliableand state-of- the-art design, neither it nor its peripheraldetection devices can off

16KEYPAD FUNCTIONSThe keypad can provide a wide assortment of utility functions. The functions are displayed in a prompting “yes/no”format. To skip a

17KEYPAD FUNCTIONS4. Display System Troubles? Displays a 1- or 2-digit error code representing aproblem detected in the system. (See SYSTEM TROUBLE ER

18KEYPAD FUNCTIONS9. Reset System Trouble? System troubles display and sound at the keypad.Correcting the trouble will clear most indications, however

19KEYPAD FUNCTIONS14. Activate EZM Zone Find? For installer's use only. If accidentally enabled,press the C button to exit.15. Activate Telephone

2The GEM-RP3DGTL is a “smart”, in-teractive, menu-driven keypad de-signed for your Napco control panel. Adigital display is provided to show thestatus

20KEYPAD FUNCTIONS17. Activate Program? (Program Mode programmed for user? YES NO.)Activates the Program Mode from Keypad No. 1 only. Note:

21Your alarm specialist may haveprogrammed your system to be moni-tored by a central station. The built-indigital communicator can transmitemergency s

22ADVANCED FEATURESSecurity Bypass/Unbypass(Security Bypass programmed? YES NO.)In high-security applications, zones may be bypassed (or un

23ADVANCED FEATURESStart Exit Time After Ringback (for Commercial Burglary Systems only)(Start Exit Time programmed? YES NO.)If your syst

24PROGRAMMING (OPTIONAL)IntroductionThe Program Mode (optional) is usedto customize User Codes. Access to theProgram Mode requires a special UserCode,

25PROGRAMMING (OPTIONAL)6. Continuing, set the cursor to theuser code with the A button and enterthe new User Code using the number but-tons. Press G0

26GLOSSARYFollowing are brief descriptions of terms and features used herein that may be unfamiliar to you. Some of the features areprogrammable optio

27GLOSSARYManager's Mode - In a partitionedsystem, a low-security operating modethat allows arming by area.Panic Buttons - Blue buttons on thekey

28GLOSSARY• Exit/Entry Follower Zone: Pro-vides exit and entry delay for inte-rior devices. Entry delay only oc-curs if re-entry takes placethrough th

29SYSTEM TROUBLE ERROR CODESE01-00 AC power failure.E02-00 System low battery.E03-00 Communication failure.E04-NN RF transmitter supervisory Failure;

3TABLE OF CONTENTSTABLE OF CONTENTSSection PageKEYPAD CONTROLS & INDICATORS...5SETTING THE

30NOTESGEM-RP3DGTL.pub page 30Wednesday, August 18, 1999 14:03

31NOTESGEM-RP3DGTL.pub page 31Wednesday, August 18, 1999 14:03

32NAPCO LIMITED WARRANTYTHE FOLLOWING STATEMENT IS REQUIRED BY THE FCC.This equipment generates and uses radio-frequency energy and, if not installed

4KEYPAD CONTROLS & INDICATORSRCOMPUTERIZED SECURITY SYSTEMARMEDSTATUSSYSTEM ARMEDSYSTEM ARMED01/01/97 12:00AM01/01/97 12:00AM1 2435 67 8 9 0

5KEYPAD CONTROLS & INDICATORSWindow. Window. Lights indicatesystem status messages; digit displayindicates related zone, function or er-ror messag

6SETTING THE ALARM (ARMING) WHEN LEAVING1. Check the keypad. The green STATUS light must be on in order to arm.• If the green light is off, the number

7SETTING THE ALARM (ARMING) WHEN LEAVINGIf you attempt to arm with a system trouble, a 3-second tone will sound at the keypad.(See SYSTEM TROUBLE ERRO

8PROTECTING YOURSELF WHILE ON THE PREMISESBypassing Interior ZonesInterior Zones, when bypassed, allow free movement within the premises whilethe prot

9PROTECTING YOURSELF WHILE ON THE PREMISESEmergency Buttons (Only available if programmed)The Blue Emergency Buttons (F, A and P), if programmed, area